Hi ! How can we help ?

Hi ! How can we help ?

[Hardware] Paper Roll Placement and Replacement

The printers of iCHEF supports are thermal printers, so the paper roll needs a thermal coating to print receipts smoothly. The size and placement of the paper roll depend on the model of the printer. Please take a look at the following content on how to place the paper roll.

How to Set the Paper Roll and Replacement

mC-Print3

Out of Paper LED Signal

When the red light is blinking, it means that the printer has run out of paper. To replace the paper, you do not need to turn off the printer.

Label Roll Specifications

  • Paper Roll width : 58 mm / 80 mm
  • Paper Roll diameter : 80 mm
  • Paper Roll length : 68 m
  • Paper Roll thickness : 0.073 mm ± 0.005 mm
  • Core diameter : 20.4 mm

How to Place the Label Roll.

  1. Gently open the paper cover of the printer by lifting the lever on the left side of the printer.
  2. Load the paper roll with the print side facing up like a whistle.
  3. Pull out a suitable paper length, ensuring that the paper cover can hold the paper in place when it is closed.

紙卷擋板

出單機支援 58mm 與 80mm 的紙卷寬度,請留意放置紙卷時,紙卷是否會出現明顯的左右移動(此狀況會導致印單時出現偏移情況)若使用 58mm 紙卷寬度時,請在紙槽內安裝紙卷擋板。

  1. 將紙卷擋板以「斜」角度避開銀色軸後,將擋板下方對準 58mm 孔位後將擋板「扶正」
  2. 向前按壓紙卷擋板,聽見卡入的聲響

mPOP

Out of Paper LED Signal

When the printer’s LED is [ blue light constantly on and red light blinking quickly ], it means running out of paper and there is no need to turn off the printer when replacing the paper roll.

Label Roll Specifications

  • Paper Roll width : 58 mm
  • Paper Roll diameter : 50 mm
  • Paper Roll length : 22 m
  • Paper Roll thickness : 0.064 mm ± 0.005 mm
  • Core diameter : 20.4 mm

How to Place the Label Roll.

  1. Gently withdraw the paper drawer, and open the paper cover on the top.
  2. Load the paper roll with the print side facing up like a whistle.
  1. Pull out a suitable paper length, ensuring that the paper cover can hold the paper in place when it is closed.

The paper does not need to be placed through the paper output, please sandwich the paper and close the printer cover. If the printer is on then the setting will be completed with the paper cut automatically.

  1. Please close the paper drawer.

TSP 100/143

Out of Paper LED Signal

When the printer’s LED is [ blue light constantly on and red light blinking quickly ], it means running out of paper and there is no need to turn off the printer when replacing the paper roll.

Label Roll Specifications

  • Paper Roll width : 58 mm / 80 mm
  • Paper Roll diameter : 80 mm
  • Paper Roll length : 68 m
  • Paper Roll thickness : 0.073 mm ± 0.005 mm
  • Core diameter : 20.4 mm

How to Place the Label Roll.

  1. Gently open the paper cover of the printer.
  2. Insert the paper roll into the printer with the thermal side facing down.
  3. Pull out a suitable paper length, ensuring that the paper cover can hold the paper in place when it is closed.

紙卷擋板

出單機支援 58mm 與 80mm 的紙卷寬度,請留意放置紙卷時,紙卷是否會出現明顯的左右移動(此狀況會導致印單時出現偏移情況)若使用 58mm 紙卷寬度時,請在紙槽內安裝紙卷擋板。

  1. 將紙卷擋板對準 58mm 孔位放置
  2. 向下按壓紙卷擋板,聽見卡入的聲響

TSP 654

Out of Paper LED Signal

When the printer’s light is [Greenlight stays on, red light keeps blinking for 0.5 seconds], it means running out of paper and there is no need to turn off the printer when replacing the paper roll.

Label Roll Specifications

  • Paper Roll width : 58 mm / 80 mm
  • Paper Roll diameter : 80 mm
  • Paper Roll length : 68 m
  • Paper Roll thickness : 0.073 mm ± 0.005 mm
  • Core diameter : 20.4 mm

How to Place the Label Roll.

  1. Gently open the paper cover of the printer.
  2. Insert the paper roll into the printer with the thermal side facing down.
  3. Pull out a suitable paper length, ensuring that the paper cover can hold the paper in place when it is closed.

紙卷擋板

出單機支援 58mm 與 80mm 的紙卷寬度,請留意放置紙卷時,紙卷是否會出現明顯的左右移動(此狀況會導致印單時出現偏移情況)若使用 58mm 紙卷寬度時,請在紙槽內安裝紙卷擋板。

  1. 將紙卷擋板對準 58mm 孔位放置
  2. 向下按壓紙卷擋板,聽見卡入的聲響

GoDEX DT2x

Out of Paper LED Signal

When the printer’s Red light stays on and there are 2 sounds of “beep”, it means that the printer has run out the paper.

The GoDEX cover is transparent, you could observe the amount to replace the paper roll in advance.

Label Roll Specifications

  • Label Width : 40 mm
  • Label Height : 30 mm
  • Interval Between Labels : 3 mm
  • Two Sides of Label from Bottom Paper : 1 mm
  • Label Thickness : 0.082 mm ± 0.01 mm
  • Amount of Labels : 1000 Labels

How to Place the Label Roll.

  1. Turn off the printer.
  2. Open the paper holder cover and lift the spindle upwards.
  3. Place the label roll onto the spindle, ensure that the labels are facing up.
  4. Pull out a suitable label length, and let the label go through the [ Label guides ] ensuring that the paper cover can hold the label in place when it is closed.
  1. Press and hold the “FEED” button, and turn on the power until the printer beeps, then release the button.
  2. Wait until the test label has finished printing, then press the ‘FEED’ button once to position the label.

Preventing Paper Jams and How to Handle it

When the printer receives a print command, it will start to execute the print job. It is recommended not to place any objects in front of the printer’s paper output port and to wait until the printer has finished printing and cutting the paper before taking the document. If a paper jam occurs, it may cause the cutter to lock (an error LED will be displayed). In this case, do not forcibly open the paper roll cover. Please check :[Hardware] Unlock the Printer Cutter

有幫助到你嗎?
沒有
© Copyright 2022 iCHEF Limited.